All series of petrol wood chippers, garden shredders and mulchers are compatible with the use of E10 Petrol.

Assembly Parts:
Battery Tray – 1
M5x125 Bolt – 2
M5 Nut – 2
Battery – 1
Ignition Key – 2

If you’re reading the original FM6DD Manual; on step 5 of page 9 of the assembly instructions, attach the battery tray to the underside of the base (42) using the 4 bolts that secure the engine to the base.

Connect the battery wires to the terminals on the battery (red to positive (+)). Place the battery on the tray and secure using two M5 x 125 bolts and nuts.

Starting the chipper

1. Position your wood chipper on flat, dry ground and make sure the machine cannot be moved.
2. Before starting, manually turn the drum to make sure it is not obstructed and moves smoothly.
3. Make sure the fuel shut-off valve is in the “ON” position.
4. Move the choke control level to the “CHOKE” position (should only be needed if the engine is warm or not starting)
5. Move the throttle control lever towards the “FAST” position. Turn the ignition key to the “START” position. As soon as the engine starts, allow the key to turn back to the “RUN” position.
6. Move the choke control lever (if used for cold engine) slowly back to the “RUN” position when the engine is running well.
7. If the Wood Chipper has not been running (cold engine), warm up the engine by running the engine at half throttle for 3 to 4 minutes, then advance the engine throttle control to the maximum speed.

Stopping the chipper

1. Move the throttle lever to “IDLE”.
2. Turn the Ignition key to the “OFF” position.

A rare case of the engine sputtering and cutting out may be due to the way in which the petrol was filled into the tank. When filling up the chipper with petrol, ensure that the funnel is completely dry and that no water is entering into the tank.

If this happens, the water sinks directly to the bottom of the tank and the engine then attempts to burn this first, resulting in the engine spluttering and cutting out.

Both the FM6DD and the FM4DDE utilise a direct drive for performance, this means that there are no belts or chains that you need to adjust.

The FM6DD Petrol Wood Chipper is capable of chipping any fresh wood. We’ve thoroughly tested the chipper with hawthorn and beech wood, both when fresh and seasoned.

It’s capable of chipping the wood when fresh, but after three or so days the wood will begin to season, and this causes issues with chipping.

If you’re planning on chipping seasoned hard wood, then you will require a power fed chipper.

This largely depends on the hardness of the wood you’re chipping. The harder the wood, the quicker the blades will need to be replaced.

However, the chipper is equipped with twin reversible blades. The reversible blades mean that you can simply switch the blades around when the first set start to dull, so you get a much longer life span on the blades.

We also stock spare blades on our website, should you need to have them replaced.

You can also sharpen your blades using an oil stone. Simply sharpen the edges of the blade, do not worry about taking out any dents or marks.

Our compact chippers are built for the primary purpose of being a chipper and shredder. However, the chipper can still handle dry green waste such as laurel and conifer.

The cutting blades are set at a 0.5mm gap, these can be adjusted to be very close together which eliminates the gap for any leaves to bypass the cutting blades.

The FM6DD spins at a higher rate (3600 rpm v 2800 rpm) than the FM4DDE, the higher spin rate means that the chipper is able to produce smaller cuttings.

This machine is not capable of mulching wet green waste such as ivy or nettles, however, our mulching machine can easily mulch pretty much any material you throw at it. Take a further look at it by clicking here. FM6DD-MUL.

Wood is too dried out

The compact chipper series is designed primarily for chipping freshly cut wood. The FM6DD has been tested thoroughly chipping freshly cut hawthorn wood (slow-grown hardwood).

We recommend that the wood is chipped no longer than three days after cutting. After this date, the wood will begin to dry out, meaning the chipper blades then struggle to dig into the wood. This produces a sawdust-like waste from the exit chute, and the chipper will struggle to self-feed.

If the chipper is producing sawdust – this is a clear sign that the wood is dry. When chipping slow-grown hardwood like fruit trees (such as cherry or apple trees) you must ensure that you chip the material the same day that it is cut to ensure the machine operates at full effectiveness.

The entrance leading direct to the cutter is 95 mm x 95 mm. The upper section has a CE plate fitted to restrict the size of cutting to 2 x 55mm holes with a slot joining the two holes which provides an entrance for side shoots and branches etc. The safety plate is not required for USA or Canada.

In order to rotate the blades on any of our chippers, you much use a hex socket (6 sided) with no leading edge, this is important or you will round off the head.

Sometimes it helps to tighten a tiny bit before undoing the bolt.

When the process is complete, use a small amount of thread lock and screw back into position.